Siemens SINAMICS G120C Modbus register haritası
Diğer adları: G120C · G120C USS/MB · SINAMICS G120C USS/MB
Siemens SINAMICS G120C için 63 Modbus register: hatta gönderilen adres, 30001 biçimindeki referans, veri tipi, byte sırası, birim ve ölçek. Kaynak: SINAMICS G120 Fieldbuses Function Manual (11/2020, FW V4.7 SP13).
SINAMICS G120C converter (USS/MB version) over Modbus RTU on RS485; 16-bit holding registers with fixed scaling factors.
- Cihaz tipi
- Motor sürücüsü
- Register sayısı
- 63
- Arayüzler
- Modbus RTU
- Varsayılan unit ID
- 1
- Byte sırası (çok register’lı değerler)
- ABCD
- Seri port ayarları
- 19200 baud, 8 data bits, even parity, 1 stop bit
Cihazda doğrulama
Henüz cihazda doğrulanmadı. Harita üretici dokümanından aktarıldı ve bir betikle dokümana karşı kontrol edildi; ilk okumaları cihazın ekranıyla karşılaştırın.
Bağlantı notları
- The manual numbers holding registers from 40001; the address here is the register minus 40001 (its example frames read 40110 at 0x006D and write 40100 at 0x0063).
- Select Modbus with p2030 = 2; address p2021 (or the address switch), baud rate p2020, parity p2031.
- Scaled registers hold value x scaling factor (factor 100 is scale 0.01 here). The main setpoint and actual value are unscaled process data.
- On/off registers list the source's on text as 1 and its off text as 0.
- The same function manual lists this register table for G120 Control Units CU230P-2, CU240B-2, CU240E-2 and CU250S-2; check their own manuals before reusing this map.
- Registers 40601-40722 (acyclic DS47 access) and 40800-40811 (multi-pump control) are left out.
- Writing the control word or setpoint moves the motor. Read-only access is the safe default.
Register’lar
Üretici dokümanındaki gruplara göre. Register adları kaynak dokümandaki gibi İngilizcedir.
Durum 3 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Status word (ZSW1)zsw1 | 40110 | 0x006D | bitfield16 | |||
Main actual valuemain_actual_value | 40111 | 0x006E | int16 | |||
Control prioritycontrol_priority | 40349 | 0x015C | uint16 |
Tanımlama 3 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Powerstack numberpowerstack_number | 40300 | 0x012B | uint16 | |||
Converter firmwareconverter_firmware | 40301 | 0x012C | uint16 | |||
Rated powerrated_power | 40320 | 0x013F | uint16 | kW | × 0.01 |
Control 2 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Control word (STW1)stw1 | 40100 | 0x0063 | bitfield16 | |||
Main setpointmain_setpoint | 40101 | 0x0064 | int16 |
Giriş ve çıkışlar 19 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
DO 0digital_output_0 | 40200 | 0x00C7 | uint16 | |||
DO 1digital_output_1 | 40201 | 0x00C8 | uint16 | |||
DO 2digital_output_2 | 40202 | 0x00C9 | uint16 | |||
AO 0analog_output_0 | 40220 | 0x00DB | int16 | % | × 0.01 | |
AO 1analog_output_1 | 40221 | 0x00DC | int16 | % | × 0.01 | |
AO 2analog_output_2 | 40222 | 0x00DD | int16 | % | × 0.01 | |
DI 0digital_input_0 | 40240 | 0x00EF | uint16 | |||
DI 1digital_input_1 | 40241 | 0x00F0 | uint16 | |||
DI 2digital_input_2 | 40242 | 0x00F1 | uint16 | |||
DI 3digital_input_3 | 40243 | 0x00F2 | uint16 | |||
DI 4digital_input_4 | 40244 | 0x00F3 | uint16 | |||
DI 5digital_input_5 | 40245 | 0x00F4 | uint16 | |||
AI 0analog_input_0 | 40260 | 0x0103 | int16 | % | × 0.01 | |
AI 1analog_input_1 | 40261 | 0x0104 | int16 | % | × 0.01 | |
AI 2analog_input_2 | 40262 | 0x0105 | int16 | % | × 0.01 | |
AI 3analog_input_3 | 40263 | 0x0106 | int16 | % | × 0.01 | |
AO 0 (write)analog_output_0_setting | 40523 | 0x020A | int16 | % | × 0.01 | |
AO 1 (write)analog_output_1_setting | 40524 | 0x020B | int16 | % | × 0.01 | |
AO 2 (write)analog_output_2_setting | 40525 | 0x020C | int16 | % | × 0.01 |
Ayarlar 4 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Current limitcurrent_limit | 40321 | 0x0140 | uint16 | A | × 0.1 | |
Ramp-up timeramp_up_time | 40322 | 0x0141 | uint16 | s | × 0.01 | |
Ramp-down timeramp_down_time | 40323 | 0x0142 | uint16 | s | × 0.01 | |
Reference speedreference_speed | 40324 | 0x0143 | uint16 | rpm |
Actual values 9 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Speed setpointspeed_setpoint | 40340 | 0x0153 | int16 | rpm | ||
Actual speed valueactual_speed | 40341 | 0x0154 | int16 | rpm | ||
Output frequencyoutput_frequency | 40342 | 0x0155 | int16 | Hz | × 0.01 | |
Output voltageoutput_voltage | 40343 | 0x0156 | uint16 | V | ||
DC link voltagedc_link_voltage | 40344 | 0x0157 | uint16 | V | ||
Current actual valueactual_current | 40345 | 0x0158 | uint16 | A | × 0.01 | |
Actual torque valueactual_torque | 40346 | 0x0159 | int16 | Nm | × 0.01 | |
Actual active poweractual_active_power | 40347 | 0x015A | uint16 | kW | × 0.01 | |
Energy consumptionenergy_consumption | 40348 | 0x015B | uint16 | kWh |
Faults 10 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Fault number, index 0fault_number_0 | 40400 | 0x018F | uint16 | |||
Fault number, index 1fault_number_1 | 40401 | 0x0190 | uint16 | |||
Fault number, index 2fault_number_2 | 40402 | 0x0191 | uint16 | |||
Fault number, index 3fault_number_3 | 40403 | 0x0192 | uint16 | |||
Fault number, index 4fault_number_4 | 40404 | 0x0193 | uint16 | |||
Fault number, index 5fault_number_5 | 40405 | 0x0194 | uint16 | |||
Fault number, index 6fault_number_6 | 40406 | 0x0195 | uint16 | |||
Fault number, index 7fault_number_7 | 40407 | 0x0196 | uint16 | |||
Alarm numberalarm_number | 40408 | 0x0197 | uint16 | |||
Actual alarm codeactual_alarm_code | 40409 | 0x0198 | uint16 |
Diagnostics 1 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
PRM ERROR codeparameter_error_code | 40499 | 0x01F2 | uint16 |
Pid 12 register
| Ad ve anahtar | Referans | Adres | Tip | Byte sırası | Birim | Ölçek |
|---|---|---|---|---|---|---|
Technology controller enabletc_enable | 40500 | 0x01F3 | uint16 | |||
Technology controller MOPtc_mop | 40501 | 0x01F4 | int16 | % | × 0.01 | |
Technology controller actual value filter time constanttc_filter_time | 40510 | 0x01FD | uint16 | × 0.01 | ||
Technology controller actual value scalingtc_feedback_scaling | 40511 | 0x01FE | uint16 | % | × 0.01 | |
Technology controller proportional gaintc_proportional_gain | 40512 | 0x01FF | uint16 | × 0.001 | ||
Technology controller integral timetc_integral_time | 40513 | 0x0200 | uint16 | s | ||
Technology controller D-component time constanttc_derivative_time | 40514 | 0x0201 | uint16 | |||
Technology controller max. limittc_max_limit | 40515 | 0x0202 | int16 | % | × 0.01 | |
Technology controller min. limittc_min_limit | 40516 | 0x0203 | int16 | % | × 0.01 | |
Technology controller effective setpointtc_effective_setpoint | 40520 | 0x0207 | int16 | % | × 0.01 | |
Technology controller actual value after filtertc_actual_value | 40521 | 0x0208 | int16 | % | × 0.01 | |
Technology controller output signaltc_output | 40522 | 0x0209 | int16 | % | × 0.01 |
Kaynak dokümanlar
- SINAMICS G120 Fieldbuses Function Manual , Siemens, A5E34229197B AG, 11/2020, FW V4.7 SP13 (erişim 2026-11-09) Section 5.4 Communication using Modbus RTU, tables 5-12 to 5-17 and the example frames in tables 5-20 and 5-23.
Adıyla okuyun
SINAMICS G120C cihazını yapay zekâ asistanıyla okuyun
Proxus Industrial MCP Server bu haritayı içerir. Haritayı cihaza tanımlayın; Claude, Cursor ya da VS Code register’ları anahtarıyla, doğru veri tipi, byte sırası, ölçek ve birimle okur. Yalnızca okur.
Bu cihaz Modbus RTU konuşur: bir Modbus TCP ağ geçidi üzerinden bağlanın; ağ geçidinin adresini ve cihazın unit ID’sini kullanın.
proxus-mcp.json
{
"devices": {
"sinamics-1": {
"protocol": "modbus-tcp",
"host": "192.168.10.40",
"unit_id": 1,
"map": "siemens/sinamics-g120c"
}
}
} Asistanınıza sorun
sinamics-1 cihazından rated_power değerlerini oku.
Yaptığı araç çağrısı
read_named(device: "sinamics-1", keys: ["rated_power"]) Bu cihaz sizde mi? Haritayı doğrulayın.
Asistanınızdan verify_device_map çalıştırmasını isteyin. Her register’ı yalnızca okuyarak bir kez okur, değerlerin makul olup olmadığını kontrol eder ve iki değeri ekranla karşılaştırmanızı ister. Bir rapor ve doldurulmuş bir GitHub kaydı hazırlar, siz gönderirsiniz; adınız bu haritanın doğrulayanlar listesine eklenir.
Çok sayıda cihazdan mı veri topluyorsunuz?
Proxus, Modbus TCP ve RTU cihazlarını makinelerin yanında okur, geçmiş veriyi saklar ve değerleri panolara, veritabanlarına ve yapay zekâya aktarır.