Siemens SINAMICS V20 Modbus register map
Also searched as: V20 · SINAMICS V20 inverter · 6SL3210-5BB · 6SL3210-5BE
77 Modbus registers of the Siemens SINAMICS V20, with the address on the wire, the 30001-style reference, data type, byte order, unit and scale. Transcribed from SINAMICS V20 Inverter Operating Instructions (01/2018).
SINAMICS V20 inverter over Modbus RTU on its RS485 port; 16-bit holding registers with fixed scaling factors.
- Device type
- Variable speed drive
- Registers
- 77
- Interfaces
- Modbus RTU
- Default unit ID
- 1
- Byte order (multi-register values)
- ABCD
- Serial settings
- 9600 baud, 8 data bits, even parity, 1 stop bit
Hardware verification
Not yet verified on hardware. The map is transcribed from the vendor document and checked against it by script; check the first readings against the device display.
Connection notes
- The manual lists each register twice, as the inverter register number and as the 40001-based Modbus number; the address here is the inverter number, which is the Modbus number minus 40001.
- Set P2023 = 2 (Modbus) and power-cycle; P0700 = 5 makes RS485 the command source. Address P2021 (default 1), baud rate P2010, parity P2034, stop bits P2035.
- Scaled registers hold value x scaling factor (factor 100 is scale 0.01 here).
- On/off registers list the source's on text as 1 and its off text as 0.
- Most values also appear in a second register set from 40200 on; only registers that the first set lacks are listed from it.
- Writing control registers or setpoints moves the motor. Read-only access is the safe default.
Registers
Grouped as in the vendor document.
Status 11 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Forward/reversestatus_forward_reverse | 40034 | 0x0021 | uint16 | |||
Stop/runstatus_stop_run | 40035 | 0x0022 | uint16 | |||
Run at maximum frequencystatus_at_max_frequency | 40036 | 0x0023 | uint16 | |||
Control modestatus_control_mode | 40037 | 0x0024 | uint16 | |||
Enabledstatus_enabled | 40038 | 0x0025 | uint16 | |||
Ready to runstatus_ready_to_run | 40039 | 0x0026 | uint16 | |||
Faultstatus_fault | 40054 | 0x0035 | uint16 | |||
Warningstatus_warning | 40059 | 0x003A | uint16 | |||
Status word (ZSW)zsw | 40110 | 0x006D | bitfield16 | |||
Actual speed (HIW)hiw | 40111 | 0x006E | int16 | |||
Hand/autohand_auto | 40349 | 0x015C | uint16 |
Identification 3 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Rated powerrated_power | 40032 | 0x001F | uint16 | kW | × 0.01 | |
Inverter versioninverter_version | 40061 | 0x003C | uint16 | × 0.01 | ||
Inverter modelinverter_model | 40062 | 0x003D | uint16 |
Settings 10 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Watchdog timewatchdog_time | 40001 | 0x0000 | uint16 | ms | ||
Watchdog actionwatchdog_action | 40002 | 0x0001 | uint16 | |||
Current limitcurrent_limit | 40010 | 0x0009 | uint16 | % | × 0.1 | |
Acceleration timeacceleration_time | 40011 | 0x000A | uint16 | s | × 0.01 | |
Deceleration timedeceleration_time | 40012 | 0x000B | uint16 | s | × 0.01 | |
Reference frequencyreference_frequency | 40016 | 0x000F | uint16 | Hz | × 0.01 | |
Fixed frequency 1fixed_frequency_1 | 40325 | 0x0144 | int16 | Hz | × 0.01 | |
Fixed frequency 2fixed_frequency_2 | 40326 | 0x0145 | int16 | Hz | × 0.01 | |
Fixed frequency 3fixed_frequency_3 | 40327 | 0x0146 | int16 | Hz | × 0.01 | |
Fixed frequency 4fixed_frequency_4 | 40328 | 0x0147 | int16 | Hz | × 0.01 |
Control 7 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Frequency setpointfrequency_setpoint | 40003 | 0x0002 | uint16 | % | × 0.01 | |
Run enablerun_enable | 40004 | 0x0003 | uint16 | |||
Forward/reverse commandforward_reverse_command | 40005 | 0x0004 | uint16 | |||
Start commandstart_command | 40006 | 0x0005 | uint16 | |||
Fault acknowledgementfault_acknowledge | 40007 | 0x0006 | uint16 | |||
Control word (STW)stw | 40100 | 0x0063 | bitfield16 | |||
Speed setpoint (HSW)hsw | 40101 | 0x0064 | int16 |
Pid 12 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
PID setpoint referencepid_setpoint_reference | 40008 | 0x0007 | int16 | % | × 0.01 | |
PID enablepid_enable | 40009 | 0x0008 | uint16 | |||
PID upper limitpid_upper_limit | 40017 | 0x0010 | int16 | % | × 0.01 | |
PID lower limitpid_lower_limit | 40018 | 0x0011 | int16 | % | × 0.01 | |
PID proportional gainpid_proportional_gain | 40019 | 0x0012 | uint16 | × 0.001 | ||
PID integral gainpid_integral_gain | 40020 | 0x0013 | uint16 | s | ||
PID differential gainpid_differential_gain | 40021 | 0x0014 | uint16 | |||
PID feedback gainpid_feedback_gain | 40022 | 0x0015 | uint16 | % | × 0.01 | |
PID low passpid_low_pass | 40023 | 0x0016 | uint16 | × 0.01 | ||
PID setpoint outputpid_setpoint_output | 40045 | 0x002C | int16 | % | × 0.01 | |
PID outputpid_output | 40046 | 0x002D | int16 | % | × 0.01 | |
PID feedbackpid_feedback | 40047 | 0x002E | int16 | % | × 0.01 |
I/O 13 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Digital output 1digital_output_1 | 40014 | 0x000D | uint16 | |||
Digital output 2digital_output_2 | 40015 | 0x000E | uint16 | |||
Analog input 1analog_input_1 | 40040 | 0x0027 | int16 | % | × 0.01 | |
Analog input 2analog_input_2 | 40041 | 0x0028 | int16 | % | × 0.01 | |
Analog output 1analog_output_1 | 40042 | 0x0029 | int16 | % | × 0.01 | |
Digital input 1digital_input_1 | 40048 | 0x002F | uint16 | |||
Digital input 2digital_input_2 | 40049 | 0x0030 | uint16 | |||
Digital input 3digital_input_3 | 40050 | 0x0031 | uint16 | |||
Digital input 4digital_input_4 | 40051 | 0x0032 | uint16 | |||
Digital output 3digital_output_3 | 40202 | 0x00C9 | uint16 | |||
Digital output 4digital_output_4 | 40203 | 0x00CA | uint16 | |||
Digital input 5digital_input_5 | 40244 | 0x00F3 | uint16 | |||
Digital input 6digital_input_6 | 40245 | 0x00F4 | uint16 |
Actual values 11 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Frequency outputoutput_frequency | 40024 | 0x0017 | int16 | Hz | × 0.01 | |
Speedspeed | 40025 | 0x0018 | int16 | rpm | ||
Current filteredcurrent_filtered | 40026 | 0x0019 | uint16 | A | × 0.01 | |
Torquetorque | 40027 | 0x001A | int16 | Nm | × 0.01 | |
Actual poweractual_power | 40028 | 0x001B | uint16 | kW | × 0.01 | |
Total kWhtotal_kwh | 40029 | 0x001C | uint16 | kWh | ||
DC bus voltagedc_bus_voltage | 40030 | 0x001D | uint16 | V | ||
Referencefrequency_reference | 40031 | 0x001E | int16 | Hz | × 0.01 | |
Voltage outputoutput_voltage | 40033 | 0x0020 | uint16 | V | ||
Actual frequencyactual_frequency_percent | 40044 | 0x002B | int16 | % | × 0.01 | |
Current unfilteredcurrent_unfiltered | 40350 | 0x015D | uint16 | A | × 0.01 |
Faults 9 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Last faultlast_fault | 40055 | 0x0036 | uint16 | |||
Fault number, index 1fault_index_1 | 40056 | 0x0037 | uint16 | |||
Fault number, index 2fault_index_2 | 40057 | 0x0038 | uint16 | |||
Fault number, index 3fault_index_3 | 40058 | 0x0039 | uint16 | |||
Last warninglast_warning | 40060 | 0x003B | uint16 | |||
Fault number, index 4fault_index_4 | 40404 | 0x0193 | uint16 | |||
Fault number, index 5fault_index_5 | 40405 | 0x0194 | uint16 | |||
Fault number, index 6fault_index_6 | 40406 | 0x0195 | uint16 | |||
Fault number, index 7fault_index_7 | 40407 | 0x0196 | uint16 |
Diagnostics 1 registers
| Name and key | Reference | Address | Type | Byte order | Unit | Scale |
|---|---|---|---|---|---|---|
Parameter error codeparameter_error_code | 40499 | 0x01F2 | uint16 |
Source documents
- SINAMICS V20 Inverter Operating Instructions , Siemens, A5E34559884-009, 01/2018 (accessed 2026-11-09) Section 7.2 MODBUS communication, mapping table; parameter list for P2010, P2021, P2034 and P2035 defaults.
Read it by name
Read the SINAMICS V20 with an AI assistant
The Proxus Industrial MCP Server includes this map. Set it on the device, and Claude, Cursor or VS Code reads registers by key with the right type, byte order, scale and unit. It only reads.
This device speaks Modbus RTU: reach it through a Modbus TCP gateway and use the gateway’s address with the device’s unit ID.
proxus-mcp.json
{
"devices": {
"sinamics-1": {
"protocol": "modbus-tcp",
"host": "192.168.10.40",
"unit_id": 1,
"map": "siemens/sinamics-v20"
}
}
} Ask your assistant
Read rated_power from sinamics-1.
The tool call it makes
read_named(device: "sinamics-1", keys: ["rated_power"]) Have this device? Verify the map.
Ask your assistant to run verify_device_map. It reads every register once, read-only, checks that the values are plausible and asks you to compare two values with the display. You get a report and a prefilled GitHub issue to submit; your name goes on this map’s verified list.
Collecting from many devices?
Proxus reads Modbus TCP and RTU devices next to the machines, keeps the history and delivers the values to dashboards, databases and AI.